-40%

Assembeld Mono LJM L20.5 Ultra low distortion Power amp board + heatsink L9-13

$ 23.69

Availability: 17 in stock
  • Return shipping will be paid by: Buyer
  • Condition: New
  • Compatible Brand: Universal
  • EAN: Does not apply
  • Country/Region of Manufacture: China
  • All returns accepted: Returns Accepted
  • Non-Domestic Product: No
  • Refund will be given as: Money Back
  • Modified Item: No
  • MPN: Does not apply
  • Item must be returned within: 30 Days
  • Restocking Fee: No
  • Custom Bundle: No
  • Brand: LJM
  • Type: Circuit board
  • Model: Universal

    Description

    The default price are for one channel amp board with heatsink. usually to built a stereo amp. will need 2 of this board.
    the board will be tested well before shipping out.
    The L20.5 sound is accurate and has very low distortion. It is a representative product of LJM HIEND.
    Excellent performance regardless of whether you use the preamp.
    The L Series 200W amplifier designed by LJM uses a special CFP output and a COSCODE input stage.
    4 pairs of imported KEC KTB817 KTD1047 power tube per channel.
    Ultra low distortion circuit, HIEND design standard.
    L20.5 amplifier parameters:
    Each PCB size: 157*50mm
    Output power 200W 8R, 400W 4R + -63V power supply.
    125W 8R, 250W 4R + -50V power supply.
    250W 4R, 500W 2R + -50V power supply
    Maximum output current 15A, output maximum voltage sine wave + -63V. (+ -65V power supply)
    Quiescent current per channel 20MA
    Static power consumption = supply voltage * 0.02 (2W + -50V)
    Power supply voltage range: + - 24V to + -65V
    Recommended supply voltage and heat sink standard:
    + -35 to + -50V, heat sink 0.5KG per channel
    + -40 to + -60V, heatsink 1KG per channel
    Gain GAIN=31 times
    Frequency response = 20-25K HZ -0.15DB.
    10HZ =-0.7DB 20K HZ=-0.05DB
    Damping coefficient > 400, 8 ohm load.
    Signal to noise ratio > 98DB.
    Input sensitivity: 2V RMS 200W 8R power
    Install the connection ID:
    VCC+ positive power supply, VEE- negative power supply, PGND power supply ground.
    IN+ input signal +, IN- input signal -
    OUT+ output signal +, the negative pole of the speaker is connected to the GND position of the power board.
    It is recommended to
    Series connection
    a bulb in the primary of the 220V transformer for testing.
    Remove the lamp after normal use.
    THD+N amplitude (+ -35V supply voltage)
    THD = 0.0015%
    IMD Intermodulation Distortion Test = 0.002 (output power 50W 8 R)
    THD+N distortion map
    THD+N= 0.001-0.002% 20HZ-20KHZ Output power 10W Load 8 ohms
    THD+N=0.001% A weighting
    Shipping time:
    Default send by air mail. to US,CA,Mexico and most Europe, Asian countries,about 15-22 business days can arrived ,to Russia, Brazil,Africa.Ukraine and some other remote countries will need 30-40 working days.
    Payment:
    We ONLY accept PayPal. Payment must be made within 3 days of the auction end time. Non-Paying bidders will be reported.
    All items will be shipped within 1-3 business days (from china)upon receipt of payment.
    We ONLY send item to buyer's registered Paypal address,Buyer must be responsible for their postal address
    Customs & duties:For cross-border transactions,.we are not responsible for tariffs and duties. However, buyers may be responsible for  actual, applicable tariffs, and duties as requested brespective country laws
    Return & Exchange:
    >> Some items return is accepted within 7 days after the buyer's receiving the item.(please see the detail describe)[In case of DOA (Dead on Arrival), please report within 3 days]
    >> Returned item has to be new, unworn and in its original condition.
    >> After getting the returned item, we will refund the customer at the item's price ( excluding the shipping costs to and from )